Which Builder Upgrades Are Worth It in a GTA New Build?

Builder-upgrades post: Unfinished GTA home under framing construction with exposed wood stud walls and an egress-window opening.

Pay the builder for anything sealed inside a wall, floor, or ceiling. Refuse to pay for anything you can screw on, hang, or install after you get the keys. That one rule answers which builder upgrades are worth it in every GTA new-build upgrade appointment you will ever sit through. The three upgrades to always buy: a bathroom rough-in, electrical panel capacity, and egress windows. The three to always skip: the frameless glass shower door, the decorative range-hood box, and the fibreglass front door.

Key Takeaways

  • Rough-ins, wiring, and structural openings cost a fraction at framing stage of what they cost to retrofit after drywall is up.
  • Cosmetic finishes – glass, tile, cabinetry, and millwork – are marked up two to three times over what a local trade charges after closing.
  • GTA buyers planning a legal basement apartment must buy egress windows, electrical capacity, and a bathroom rough-in from the builder; those items cannot be added cleanly once the foundation is poured and the walls are closed.
  • Phase 1 upgrade deadlines are tied to the construction schedule, not to your closing date; some items disappear from the list once framing begins.
  • Upgrade payments are typically due on a shorter timeline than closing and are not covered by your mortgage, so budget for them separately.

The One Rule That Decides Every Upgrade

Apply the drywall test: if adding something later means opening a wall, cutting concrete, or pulling a permit for a utility reconnection, buy it now. If you can install it yourself on a Saturday afternoon, or hire a trade after you move in without touching the structure, skip it at the design centre.

A builder rough-in is the plumbing, wiring, or framing provision installed before the walls close. It costs relatively little at framing stage because the trades are already on site and the walls are open. After closing, the same work requires cutting drywall, fishing wire, patching, repainting, and sometimes a permit. The price multiplies. Some items become physically impractical.

Structural upgrades – window openings, electrical capacity, gas lines, in-wall conduit – fall on the buy side of that line. Decorative finishes fall on the skip side. The comparison table below applies this logic to ten common items on a GTA builder’s upgrade list.

New build home at the rough-in stage with exposed wiring and plumbing before drywall

Builder Upgrade Comparison: Buy or Wait?

Pricing varies by builder, model, and the Schedule “ST” in your Agreement of Purchase and Sale. Some items may already be standard in your home.

UpgradeTypical Ontario CostBuy from Builder or Do It LaterWhy
Enlarged basement windows~$400 eachBuyEgress requires cutting concrete – impossible to add cleanly after the foundation is poured
Water line to the fridgeUnder $500BuyRuns inside the wall; retrofitting means opening drywall
200 amp electrical panel~$2,000BuyUpgrading after closing requires a permit, an electrician, and a utility reconnection
36-inch range provision$500–$800BuyThe gas line and electrical circuit run behind the wall during framing
TV plug inside the wall$300–$450 eachBuyIn-wall conduit is a framing-stage item; surface raceways are the retrofit alternative
Gas line to the stove$1,000–$1,500BuyAdding gas after closing requires a licensed contractor, permit, and utility connection
Pot lights~$400 each, minimum 4 per roomSelectiveBuy only in vaulted ceilings, hallways, and rooms above a finished floor
Fibreglass double front door$2,000–$3,000SkipA door company installs after closing for the same price or less
Frameless glass shower door$3,000+SkipA glass company installs after closing for significantly less
Decorative wood box around range hoodClose to $6,000SkipA local millworker builds a custom version after closing for a fraction of the cost

Buy These from the Builder

Enlarged Basement Windows (~$400 each)

Buy these without hesitation. Egress-sized windows require cutting through the foundation wall and pouring a new concrete window well – work that is straightforward during construction and disruptive and expensive once the foundation is backfilled. Retrofitting a single egress window after closing can cost several times the builder price, and the result is rarely as clean. If a legal basement apartment is part of your plan, this is not optional.

Water Line to the Fridge (Under $500)

Buy this now. The line runs inside the kitchen wall during framing. After drywall, adding it means opening the wall, patching, and repainting – easily $500 to $1,000 in trades and finishing work for something the builder charges under $500 to do while the wall is open. It is one of the clearest value items on any new build upgrades GTA list.

200 Amp Electrical Panel (~$2,000)

Buy the larger panel. Upgrading from 100 amp to 200 amp after closing requires a licensed electrician, a permit, and a utility reconnection – a process that can run $3,000 to $5,000 or more depending on the utility’s scheduling. If you plan an EV charger, a basement apartment, or any high-draw appliances, the base panel will not be enough. Builder upgrade cost in Ontario for the panel upgrade is modest relative to the retrofit alternative.

36-Inch Range Provision ($500–$800)

Buy the provision, not necessarily the range. The gas line and dedicated electrical circuit run behind the wall during framing. After closing, adding that infrastructure means opening the wall, running new lines, and pulling a permit. The provision costs $500 to $800 from the builder. The retrofit costs multiples of that. You can buy the range itself wherever you like.

TV Plug Inside the Wall ($300–$450 each)

Buy in-wall conduit for every room where you plan a wall-mounted television. The alternative after closing is a surface raceway – a plastic channel that runs along the baseboard and looks exactly like what it is. In-wall conduit is a framing-stage item because the trades need open walls to run it. At $300 to $450 per location, it is cheap insurance against a visible workaround.

Gas Line to the Stove ($1,000–$1,500)

Buy this if you want gas cooking. Adding a gas line after closing requires a licensed gas contractor, a permit, and a utility connection – a process that can cost $2,000 to $4,000 depending on how far the line needs to run and your municipality’s requirements. The builder runs the line during framing for $1,000 to $1,500. This is one of the structural upgrades vs cosmetic upgrades decisions where the math is straightforward.

Skip These and Do Them After Closing

Fibreglass Double Front Door ($2,000–$3,000)

Skip this at the design centre. A door company can supply and install a comparable or superior fibreglass door after closing for the same price range or less, with a wider selection than the builder’s catalogue. The rough opening is already framed; swapping a door is a half-day job. Spend the builder’s markup on something structural instead.

Frameless Glass Shower Door ($3,000+)

Skip this. A glass company measures your finished shower after closing and installs a custom frameless door – often for significantly less than the builder’s price. The builder charges a premium because the design centre is a captive market. This is one of the clearest examples of new construction upgrades worth the money only when bought from the right source, and that source is not the builder’s catalogue.

Decorative Wood Box Around the Range Hood (Close to $6,000)

Skip this entirely. A local millworker builds a custom version after closing – sized precisely to your kitchen, in the wood species and stain you actually want – for a fraction of what the builder charges. At close to $6,000, this is one of the most aggressively marked-up items on a GTA builder’s upgrade list. Save the money and hire a millworker six months after you move in.

A Note on Pot Lights (~$400 each, minimum 4 per room)

Pot lights are a selective buy. In most rooms above an unfinished basement, an electrician can cut them in after closing without opening the ceiling – the work runs from below through the unfinished space. Buy pot lights from the builder only in vaulted ceilings, hallways, and rooms above a finished floor or garage, where a later install means cutting into a finished ceiling, patching, and repainting. At roughly $400 per light with a four-light minimum per room, the cost adds up quickly for rooms where the retrofit is straightforward.

What Upgrades Do I Need for a Legal Basement Apartment?

In Brampton, Mississauga, and Caledon, a legal second unit is why many buyers can carry the mortgage. The rental income offsets a meaningful portion of monthly carrying costs – and the upgrades that make it possible are all structural, all builder-stage items.

Egress windows. Every bedroom in a legal second unit requires a window large enough to serve as an emergency exit. The Ontario Building Code sets minimum dimensions. The builder cuts the opening and installs the window during foundation work. After closing, this requires cutting through the foundation wall – expensive, disruptive, and sometimes structurally complicated depending on the home’s design.

Electrical capacity. A second unit running its own appliances, HVAC, and lighting needs adequate panel capacity. A 200 amp panel is the practical minimum for a home with a basement suite. Buy the upgrade from the builder.

Bathroom rough-in. A rough-in installs the drain, supply lines, and vent stack for a future bathroom before the concrete floor is poured. After closing, adding a bathroom in the basement without a rough-in means breaking concrete – a messy, expensive job. With a rough-in, a plumber connects the fixtures in a day. The builder rough-in is one of the highest-value items on the list.

Side entrance. A separate entrance for the basement unit is usually a Phase 2 or municipal item, not something the builder includes in Phase 1 selections. Some municipalities have programs that assist with side-entrance construction. Confirm with your city what is available and what the process requires. If you are still shopping, it is worth filtering for Brampton homes with a separate entrance or Mississauga homes with a separate entrance already in place.

Legal status for a second unit depends on municipal second-unit registration, the Ontario Fire Code, and the Ontario Building Code – not on what the builder installs. Confirm the registration process, required inspections, and any zoning conditions with your municipality and your lawyer before you close. Rules differ between Brampton, Mississauga, and Caledon, and they change.

If you are also weighing the ongoing ownership costs of carrying a second unit, Ontario property tax rates for 2026 are worth reviewing as part of your full carrying-cost picture.

What Is the Difference Between a Phase 1 and Phase 2 Upgrade Appointment?

Phase 1 covers structural, electrical, plumbing, and cabinetry selections. These are chosen early – often within weeks of signing – because they affect the permit drawings and the construction schedule. Rough-ins, panel upgrades, window openings, gas lines, and kitchen layout changes are all Phase 1 items. Miss the deadline and some of them disappear from the list permanently, because framing has already started.

Phase 2 is the décor appointment: flooring, tile, countertops, stain colours, cabinet hardware, and similar finish selections. These happen later in the construction timeline and carry more flexibility, because they do not affect the structure. They are also the items most aggressively marked up. Most of what you select in Phase 2 can be done after closing by a local trade for less money.

Phase 1 deadlines are unforgiving. Builders move on construction schedules, not on buyer availability. If you are buying a townhome in the GTA, the Phase 1 window can be shorter than for a detached home because the unit is part of a larger block with a shared construction timeline.

Builder design centre display with flooring, tile, countertop and cabinet samples

A Realistic Upgrade Budget

Most GTA new-build buyers spend meaningfully more on upgrades than they planned. The design centre is designed to sell. You walk in with a number in mind and walk out with a longer list.

Budget for the structural items first – rough-ins, panel, windows, gas lines, in-wall conduit. Total those up. Then decide what, if anything, from Phase 2 is worth paying the builder’s price for. For most buyers, the answer is very little.

Upgrade payments are typically due on a shorter timeline than closing. Depending on the builder’s schedule, you may owe upgrade deposits within weeks of your design centre appointment. That money is not covered by your mortgage – it comes from your own funds. Factor it into your cash-flow plan alongside your down payment and new-build closing costs, which include HST, development charges, and adjustments.

A practical approach: allocate a firm budget for Phase 1 structural items, set a hard ceiling for Phase 2, and plan to spend the remainder after closing with local trades at market rates.

Frequently Asked Questions

Which builder upgrades are actually worth the money?

Structural and mechanical upgrades sealed inside the walls are worth the money: bathroom rough-ins, electrical panel upgrades, egress windows, gas lines, in-wall conduit, and water lines. These are difficult or impossible to add after closing. Cosmetic finishes – glass doors, millwork, tile – are not worth the builder’s price because a local trade installs them after closing for less.

Should I get upgrades from the builder or do them after closing?

Buy from the builder anything that requires open walls or an open foundation to install. Do everything else after closing. The builder’s design centre is a captive market with markups of two to three times what a local trade charges. Glass, tile, cabinetry, doors, and decorative millwork all fall into the “do it later” category.

What is a rough-in and why does it matter?

A rough-in is the plumbing, wiring, or framing provision installed before the walls close. For a bathroom, it means the drain, supply lines, and vent stack are in place under the concrete floor. After closing, adding a rough-in requires breaking concrete. Buying a rough-in from the builder is one of the highest-value decisions a new-build buyer makes.

Which upgrades do I have to get from the builder because I can’t add them later?

Egress windows, bathroom rough-ins, electrical panel upgrades, gas lines, in-wall conduit, and water lines to appliances must be purchased from the builder. All of these require open walls, open foundations, or utility connections that are far more expensive and disruptive to arrange after the home is built and drywalled.

How much do builder upgrades cost in Ontario?

Builder upgrade costs in Ontario vary widely. Structural items range from under $500 for a fridge water line to roughly $2,000 for a panel upgrade. Cosmetic items are where the markups are steepest: a decorative range-hood box can run close to $6,000 from the builder and a fraction of that from a local millworker. Review the Schedule “ST” in your Agreement of Purchase and Sale for your specific pricing.

Are pot lights worth it from the builder?

Only in specific locations. Buy pot lights from the builder in vaulted ceilings, hallways, and rooms above a finished floor or garage, where a later install requires cutting into a finished ceiling. In rooms above an unfinished basement, an electrician can add pot lights after closing without opening the ceiling, making the builder’s price harder to justify at roughly $400 per light with a four-light minimum.

Can I add a gas line after closing?

Yes, but it is significantly more expensive. Adding a gas line after closing requires a licensed gas contractor, a permit, and a utility connection. Depending on how far the line needs to run, the total cost can reach $2,000 to $4,000 or more. The builder installs the same line during framing for $1,000 to $1,500. Buy it now.

What is the difference between a Phase 1 and Phase 2 upgrade appointment?

Phase 1 covers structural, electrical, plumbing, and cabinetry selections tied to the permit drawings and construction schedule. Phase 2 covers décor: flooring, tile, counters, and hardware. Phase 1 deadlines are firm – some items are removed from the list once framing starts. Phase 2 offers more flexibility, and most Phase 2 items can be done after closing by local trades for less money.

Do builder upgrades add resale value?

Structural upgrades – additional bathrooms, electrical capacity, egress windows, higher ceilings – tend to hold value at resale because buyers cannot easily add them. Cosmetic upgrades return less: industry estimates suggest builder finish upgrades return roughly 50 cents on the dollar at resale. Spend on structure; save cosmetic decisions for after closing when you control the cost.

What new build upgrades are worth it for a GTA townhome specifically?

For a GTA townhome, prioritize the bathroom rough-in, electrical panel, in-wall conduit, and any gas provisions. Townhome Phase 1 windows can be shorter than for detached homes because units share a construction timeline. Egress windows matter if a basement suite is part of your plan. Skip the design-centre finishes – a townhome’s smaller footprint makes after-closing trades even more cost-effective.

Talk to Mandeep Dhesi Before Your Phase 1 Appointment

A pre-construction upgrade review before your Phase 1 appointment takes less than an hour and can save you thousands. Contact Mandeep Dhesi, Broker and Team Lead, Aura Key Realty, at 647-905-0370 to go through your upgrade list before you sit down at the design centre.

Sources: City of Brampton – Additional Residential Units | Statistics Canada – Residential Building Construction Price Index, Q1 2026

Recent Blogs

Get Floor Plans & Prices